Plumbing 101: Tips for Bathtub Installation

Book Maintenance

We've found this great article involving How to Install a Bathtub below on the net and concluded it made sense to share it with you on this page.


Tools You Need to Install a New Bathtub
Mounting a bath tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old bathtub is easily accessible, the project can move immediately; if you have to open up a wall surface to remove the old tub and also place the new bathtub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and also set in the brand-new one. Make certain you have actually qualified yourself for the task and also fit attempting it. As opposed to hiring a professional to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This short article will certainly aid you mount a new bath tub in your shower room if you have actually already purchased a new bathtub and do not need to alter the arrangement of your previous water pipes.
Your tools and also material list ought to make up the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installment


    To start with, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets system to prevent stress on the bathtub.
    Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use every one of the supplied washers.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.

    Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is separate the water system. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be fairly troublesome because of the limited gain access to that is usually the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
    Before going on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Bath tub


    Using both wood boards under its feet, put the bath tub in the called for placement. The wood boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
    The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bathtub until the spirit level checks out degree.
    To install faucets, fit all-time low of the furthest flexible tap adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
    Activate the water and also examine all joints and brand-new pipework for leakages and tighten them if necessary. Fill the bathtub and likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also securing around the tub should wait up until the tub has been utilized at least once as this will settle it into its final position.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the existent supply pipes.
    If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Protect the tap in place with the manufacturer supplied backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The previous kind should be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the area where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to split a stiff seal, causing the water to permeate the wall between the bathroom and the tiling, leading to complications with dampness and feasible leaks to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes and cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the activity experienced when the tub is in usage. The sealer can fracture rather early if you do not take into account this motion before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly offered on the market. It is suggested to fit the tiles using water-resistant or water-proof sticky as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Tools You Need to Install a New Bathtub

    I am very fascinated by Tools You Need to Install a New Bathtub and I really hope you enjoyed reading the new post. Sharing is nice. Helping others is fun. I thank you for reading our article about How to Install a Bathtub.


    Fast solution? Ring!

    Leave a Reply

    Your email address will not be published. Required fields are marked *